WX3000E系列AC,用命令oap connect slot 0 切换至交换板的密码忘记了,telnet登陆交换板的密码也忘记了,可以采取跳过AC板跟交换板的配置重新启动来修改配置解决。
一、wx3000
3000(3010、3024、3008)交换侧与无线侧共用忽略配置启动标志。
重启设备,ctrl+b进入bootware菜单选择6忽略配置,两侧同时忽略。
二、wx3000E(3010e、3024e):
1.ac侧,端口1配置成shutdown
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]shutdown
2. ac侧,保持配置
3. 重启设备
4. 重启后,由于端口1是down的,交换侧获取不到版本一起在request状态,o c s 0登录交换侧应该是下面的这个态
Press CTRL+K to quit.
Connected to OAP.
Request File:
Request File:
Request File:
Request File:
Request File:
Request File:
Request File:
Request File:
Request File:
Request timer out!
System restart now
Starting......
<----- 5. 交换侧长时间获取不到版本会重启本侧,等待启动时ctrl+b进入bootware,选6 skip配置,然后选0,重启交换侧Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare....
The Extend BootWare is self-decompressing.......Done!
****************************************************************************
* *
* H3C WX3010E-LSW BootWare, Version 2.00 *
* *
****************************************************************************
Copyright (c) 2004-2013 Hangzhou H3C Technologies Co., Ltd.
Compiled Date : Jan 8 2013
CPU Type : 98DXH325
CPU L1 Cache : 32KB
CPU Clock Speed : 333MHz
Memory Type : DDR2 SDRAM
Memory Size : 128MB
Flash Size : 16MB
CPLD Version : 002
PCB Version : Ver.C
Mac Address : 5CDD7035C775
Press Ctrl+B to enter extended boot menu...
BootWare password: Not required. Please press Enter to continue.
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
=====================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 6
===============
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
======================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 0
Starting......
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare....
The Extend BootWare is self-decompressing.......Done!
......
6. ctrl+k退回到无线侧,将端口1,undo shutdown,交换侧开始获取版本并跳过配置启动;